{"product_id":"pixhawk-ppm-encoder-module-1","title":"Pixhawk PPM Encoder Module","description":"Are you want to be an Electronic Geek in the future and want to build your own drone then this PPM Encoder is best for you. Pulse position modulation (PPM) encoding is the system where encoding is carried out by positioning the pulses. The PPM encoder allows to encode up to 8 PWM (pulse width modulated) signals into one PPM (pulse position modulation) signal. \u003cbr\u003e\u003cbr\u003eSome flight controllers such as the Pixhawk autopilot only support PPM (pulse position modulation) compatible receivers. If you have a PWM (pulse width modulated) receiver, you will need a PPM encoder such as this one for it to work with a PPM-only FC. \u003cbr\u003e\u003cbr\u003eThis PPM encoder will encode regular PWM inputs into a single PPM output. This allows you to combine up to 8 channels from a regular RC receiver to a single wire PPM input for your flight controller e.g. Pixhawk or APM. The nice thing about PPM is that it will enable you to reduce all channels to a single wire, excluding ground and power lines.\u003cbr\u003e\u003cbr\u003eImportant Things to be Watch While Powering The Encoder: The jumper JP1 has been included to provide some flexibility in the way you power the receiver, servos, and PPM Encoder. Often the power for the receiver, servos, and PPM Encoder will come from the autopilot board.\u003cbr\u003e\u003cbr\u003eIn this case, JP1 should be in place (shorted). \u003cbr\u003e\u003cbr\u003eOn another way, if the receiver or any servos are directly connected to the separate\/additional power source and the autopilot’s +5V is also connected to the PPM Encoder via the PPM connector – Then You Must Remove jumper JP1. This will isolate the autopilot power supply from the separate receiver power supply. Failure to remove JP1 will likely damage the autopilot’s +5v switching regulator!\u003cbr\u003e\u003cbr\u003eNote: \u003cbr\u003e\u003cbr\u003eThe firmware comes pre-configured to read 8 Channels. In case you would like to change the settings of the PPM encoder to invert the PPM signal and change the fail-safe pre-defined values you will need an AVR ISP programmer in order to reprogram it.\u003cbr\u003e\u003cbr\u003e\n\u003cdiv class=\"product_info\"\u003e\n\u003ch3 class=\"sing--sub-heading\"\u003eTechnical Details\u003c\/h3\u003e\n\u003cdiv id=\"p_info\"\u003e\n\u003cul class=\"pro-ds\"\u003e\n\u003cli\u003eInput Channel : 8 PWM channel\u003c\/li\u003e\n\u003cli\u003eOutput channel : 1 PPM channel\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"product_info\"\u003e\n\u003ch3 class=\"sing--sub-heading\"\u003ePhysical Attributes\u003c\/h3\u003e\n\u003cdiv id=\"p_info\"\u003e\n\u003cul class=\"pro-ds\"\u003e\n\u003cli\u003ePWM signal cable length (mm) : 60\u003c\/li\u003e\n\u003cli\u003ePPM signal cable length (mm) : 90\u003c\/li\u003e\n\u003cli\u003eL x W x H (mm): 31.60 x 23 x 8\u003c\/li\u003e\n\u003cli\u003eWeight (gm) : 10\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"product_info\"\u003e\n\u003ch3 class=\"sing--sub-heading\"\u003eProduct Video\u003c\/h3\u003e\n\u003cdiv id=\"p_video\"\u003e\u003ciframe title=\"YouTube video player\" src=\"https:\/\/www.youtube.com\/embed\/B-tgEKK4Hes\" height=\"400\" width=\"800\" allowfullscreen=\"\" allow=\"accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture\" frameborder=\"0\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"product_info\"\u003e\n\u003ch3 class=\"sing--sub-heading\"\u003eDocumentation\u003c\/h3\u003e\n\u003cdiv id=\"p_info\"\u003e\n\u003cul class=\"pro-ds ls-n\"\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/drive.google.com\/file\/d\/1vhInX3YFtkmgYJpMEJq3Ga8uk0-_VxFJ\/view?usp=sharing\" target=\"_blank\"\u003eDatasheet\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"product_info\"\u003e\n\u003ch3 class=\"sing--sub-heading\"\u003ePackage Includes\u003c\/h3\u003e\n\u003cdiv id=\"p_info\"\u003e\n\u003cul class=\"pro-ds\"\u003e\n\u003cli\u003e1 x Pixhawk PPM Encoder Module.\u003c\/li\u003e\n\u003cli\u003e1 x JR plug 10P input end of the cable.\u003c\/li\u003e\n\u003cli\u003e1x JR plug 4P output end of the cable.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","brand":"KitsGuru","offers":[{"title":"Default Title","offer_id":40708948263093,"sku":"KG721","price":699.0,"currency_code":"INR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0587\/2130\/4757\/products\/ppm-encoder-v1-0-for-pixhawk-ppz-mk-mwc-megapirate-apm-flight-controller-2.jpg?v=1648444669","url":"https:\/\/kitsguru.com\/fr\/products\/pixhawk-ppm-encoder-module-1","provider":"KitsGuru","version":"1.0","type":"link"}