OLED 0.96 inch, 7 Pin SPI Interface
- Product SKU: KLCD048
Need Volume Discounts? Deals are specially designed for you. Click here
Need Customization? Provide us more details Click here
Warehouse Details
Specification
Description
0.96 Inch Blue White Yellow-Blue SPI (default) / IIC 0.96 inch OLED display 7 Pin, no need for a backlight, self-illumination, the performance is better than the traditional LCD, also lower consumption. Explore the Brilliance: OLED Display with 7 Pin Configuration at an Unbeatable OLED Price!
128×64 LED display module for Arduino supports many control chips. Fully compatible with Arduino, 51 Series, MSP430 Series, STM32 / 2, CSR IC, etc. Ultra-low power consumption: full screen lit 0.08W Super high brightness and contrast are adjustable With embedded driver/controller Interface type is IIC I2C/IIC Interface, need 2 IO only.
Note: Available best oled price Text Colours are Blue, Yellow, and Blue-Yellow leading its lead wire to disconnect.
Key Features Of 0.96 inch OLED display 7 Pin
- Driver IC: SSD1306.
- The default is a 4-wire SPI bus, which can choose a 3-wire SPI bus or an IIC bus.
- Size: 0.91 inch OLED.
- Resolution: 128 x 64 SPI / IIC interface
- Visual Angle:160°
- Input Voltage: 3.3V ~ 6V
- Compatible I/O Level: 3.3V, 5V
Interface Definition 0.96 inch OLED display 7 Pin :
NOTE: SPI is Default Setting. How to change to IC2 Below Thanks to Chas Haka for updating the Default setting.This module supports IIC, 3-wire SPI, and 4-wire SPI interface bus mode switching (see Datasheet change to IC2).
The Details Are As Follows:
Using 4.7K resistance to soldering only R3 and R4 resistors, choose a 4-wire SPI bus interface (default).Using 4.7K resistance to solder only R2 and R3 resistors, select a 3-wire SPI bus interface.
Using 4.7K resistance to solder only R1, R4, R6, R7, and R8 resistors, select the IIC bus interface.
After the interface bus mode is switched, you must select the corresponding software and wiring pins (as shown in Figure 1) for the module to operate normally.
The Corresponding Wiring Pins Are Described As Follows:
select the 4-wire SPI bus interface, all pins need to be used.Select the 3-wire SPI bus interface, only the DC pin does not need to be used(it can not be connected), other pins need to be used.
Select the IIC bus interface, only need to use the four pins GND, VCC, D0, and D1, At the same time, the RES pin is connected to the high level (can be connected to the VCC), the DC, and CS pins are connected to the power GND. Unbeatable OLED Price Alert: 0.96 Inch Display Offers Revealed
Technical Details of 0.96 inch OLED display 7 Pin
- Screen Size : 0.96(inch)
- Screen Type: OLED
- Driver IC: SSD1306
- Resolution: 128*64 (Pixel)
- Module Interface: 3-line?4-line SPI?IIC interface
- Active Area: 21.744x10.864 (mm)
- Touch Screen Type: have no touchscreen
- Visual Angle:160°
- Operating Temperature: -20?~60?
- Storage Temperature: -30?~70?
- Operating Voltage: 3.3V~5V
Pin Description of 0.96 inch OLED display 7 Pin
- GND (Power ground)
- VCC (Power + 3.3-5V)
- D0 (SPI clock line for SPI interface and IIC clock line for IIC interface)
- D1 (SPI data line for SPI interface and IIC data line for IIC interface)
- RES (OLED reset, OLED needs to be reset once after the power-on)
- DC (SPI data/command selection pin, used to set IIC address when IIC interface)
- CS (OLED SPI chip select, active low, if you do not want to use must be grounded)
Additional Details
- No need for the backlight
- The display is self-illuminating
- Power requirement is low
- They are offering a large viewing angle
- Fully compatible with Arduino
- Factory configured for SPI protocol (can easily change to IIC)
- Better performance characteristics than traditional LCD and LED displays.
- Only Need 2 I/O Port Control
Physical Attributes
- Module PCB Size: 27.3x27.8 (mm)
- Weight (gm): 8
Product Video
Documentation
Documentation
Package Includes
- 1 x OLED 0.96 inch, 7PIN SPI Interface
