Hobbywing 5V/6V 3A Switch-Mode Ultimate BEC Voltage Regulator
Review: 5 - "A masterpiece of literature" by John Doe, written onMay 4, 20020
Great
-26%
Hobbywing 3A UBEC 5V 6V max 5A Lowest RF Noise BE (HWBEC)
Hobbywing 3A UBEC 5V 6V max 5A Lowest RF Noise BE (HWBEC)
Hobbywing 3A UBEC 5V 6V max 5A Lowest RF Noise BE (HWBEC)

Hobbywing 5V/6V 3A Switch-Mode Ultimate BEC Voltage Regulator

Available:Out of Stock
  • Product SKU: KG644
Wishlist
₹ 369 ₹ 499
Successful pre-order.Thanks for contacting us!
Secure

Specification

Description

5V 3A UBEC Fully Shielded Anti-Interference Switching Power Supply for RC Helicopter, Drone and Servo

The 5V/6V 3A Fully Shielded UBEC is a compact, lightweight, and efficient switching-mode DC-DC voltage regulator designed for RC helicopters, airplanes, drones, multirotors, and robotics projects. Featuring a selectable 5V or 6V output with 3A rated current, this UBEC converts higher battery voltage into a stable regulated power supply for RC receivers, gyroscopes, servos, and other compatible electronic devices.

The module supports an input voltage range of 5.5V–26V DC and is compatible with 2S–6S LiPo and 5–18 cell NiMH battery packs. Featuring a shielded circuit design, ferrite ring noise filter, overcurrent protection, and overheat protection, it helps reduce electromagnetic interference and provides efficient voltage conversion. Its compact 41.6 × 16.6 × 7mm dimensions and 11g weight make it suitable for RC aircraft electronics and external BEC power supply applications.

Features

  • Selectable 5V/3A and 6V/3A DC output
  • Wide 5.5V–26V DC input voltage range
  • Compatible with 2S–6S LiPo batteries
  • Supports 5–18 cell NiMH battery packs
  • Efficient switching-mode DC voltage regulation
  • Maximum efficiency of nearly 90%
  • Shielded PCB for reduced electromagnetic interference
  • Ferrite ring filter attached to output wires
  • Built-in overcurrent and overheat protection
  • Compact and lightweight 11g construction
  • Suitable for receivers, gyroscopes, and servos

Working Principle

The 3A Switch-Mode UBEC operates using a switching DC-DC voltage regulation system. It converts an input voltage of 5.5V–26V DC from a battery pack into a regulated 5V or 6V output for powering compatible RC electronic devices.

Unlike traditional linear BEC regulators, the switching-mode design reduces unnecessary power dissipation and improves conversion efficiency. According to the manufacturer manual, the UBEC can achieve nearly 90% maximum efficiency, helping reduce heat generation during operation.

The shielded circuit and ferrite ring help suppress electromagnetic interference that may affect nearby RC receivers. The module also includes overcurrent and overheat protection for improved operating reliability.

Input and Output Wire Connection

  • Input Red Wire: Battery Positive (+)
  • Input Black Wire: Battery Negative (-)
  • Output Red Wire: Regulated 5V or 6V Positive (+)
  • Output Black Wire: Ground (-)
  • Output White Wire Position: Receiver Signal Position, Not Used for UBEC Signal Generation
  • Output Connector: RC Receiver Servo-Style Connector
  • Voltage Selection: 5V / 6V Switchable Output
Note: Verify the actual connector pinout and selected output voltage before connecting electronic devices. Never apply the battery input voltage directly to a receiver that requires regulated power.

Compatible Batteries and Devices

  • 2S–6S LiPo Battery Packs
  • 5–18 Cell NiMH Battery Packs
  • Compatible RC Receivers
  • 5V and 6V RC Servos
  • RC Gyroscope Modules
  • RC Airplanes and Helicopters
  • Multirotor and Drone Electronics
  • Robotics and DIY Electronic Projects
Note: Always check the voltage compatibility and combined current requirements of connected electronic devices before use.

Technical Details

  • Item Type: UBEC Voltage Regulator
  • Product Type: Switching-Mode DC-DC Regulator
  • Model: 3 Amp Switch-Mode UBEC
  • Output Voltage: 5V / 6V Selectable
  • Rated Output Current: 3A
  • 5V Output Mode: 5V / 3A
  • 6V Output Mode: 6V / 3A
  • Input Voltage: 5.5V–26V DC
  • Compatible LiPo Battery: 2S–6S
  • Compatible NiMH Battery: 5–18 Cells
  • Output Ripple: Less Than 50mVp-p at 2A / 12V Input
  • Maximum Efficiency: Nearly 90%
  • Regulator Type: Switch-Mode
  • Protection: Overcurrent and Overheat
  • Interference Reduction: Shielded PCB and Ferrite Ring
  • Input Connection: Red and Black Power Wires
  • Output Connection: RC Receiver Connector
  • Module Length: 41.6mm
  • Module Width: 16.6mm
  • Module Height: 7mm
  • Weight: 11g
  • Application: Regulated Power Supply for RC Electronics

Output Voltage Selection

  • 5V Mode: Regulated 5V DC Output
  • 6V Mode: Regulated 6V DC Output
  • Rated Output Current: 3A
  • Voltage Regulation: Switching DC-DC Conversion
Note: Disconnect battery power before changing the voltage setting. Verify the selected output voltage with a multimeter before connecting sensitive electronic components.

Switching BEC vs Linear BEC

The Switch-Mode UBEC provides improved power efficiency compared with a conventional linear BEC, particularly when converting higher battery voltage to a lower output voltage.

The supplied manual provides the following example for a 14.8V battery input and 5V/1A regulated output:
  • Input Voltage: 14.8V
  • Output Voltage: 5V
  • Output Current: 1A
  • Linear BEC Efficiency: Approximately 33.8%
  • Switch-Mode UBEC Input Current: Approximately 0.38A
  • Switch-Mode UBEC Efficiency: Approximately 89.3%

Applications

  • RC receiver power supply
  • RC servo voltage regulation
  • RC helicopter electronics
  • Multirotor and quadcopter projects
  • RC airplane control systems
  • External BEC power supply
  • Robotics and DIY electronics projects

Physical Attributes

  • Module Length: 41.6mm
  • Module Width: 16.6mm
  • Module Height: 7mm
  • Weight: 11g
  • Construction: Shielded Electronic Module
  • Noise Filter: Ferrite Ring
  • Input Cable: Red and Black Wires
  • Output Cable: Receiver-Style Connector
  • Compact and Lightweight Design

Installation and Usage Instructions

  • Disconnect the battery before installation.
  • Select the required 5V or 6V output setting.
  • Connect the UBEC input red wire to battery positive (+).
  • Connect the UBEC input black wire to battery negative (-).
  • Verify the regulated output voltage before connecting the receiver.
  • Connect the UBEC output connector to an available receiver channel.
  • If the ESC does not have a built-in BEC, no modification to the ESC receiver cable is required.
  • If the ESC has a built-in BEC, isolate its red receiver power wire before using the external UBEC.
  • Keep the ESC signal and ground connections intact.
  • Install the UBEC at least 5cm away from the receiver.
  • Secure all wiring and verify the connections before applying power.
  • Test the receiver and connected servos under normal operating conditions.
Note: When disconnecting the built-in ESC BEC output, the red power pin can be carefully removed from the receiver connector and insulated for future use.

Frequently Asked Questions (FAQs)

  • What is the function of this UBEC? It converts higher battery voltage into regulated 5V or 6V DC power.
  • What is the rated output current? 3A at either selected voltage.
  • What is the input voltage range? 5.5V–26V DC.
  • Which batteries are compatible? 2S–6S LiPo and 5–18 cell NiMH batteries.
  • Does it reduce electromagnetic interference? Yes, it uses PCB shielding and a ferrite ring filter.
  • Does it provide overcurrent protection? Yes, according to the supplied manual.
  • Does it provide overheat protection? Yes, according to the supplied manual.
  • Can it power RC servos? Yes, compatible servos within the available 3A output rating.
  • Can it replace an ESC's built-in BEC? Yes, when the existing BEC power output is properly isolated.
  • What is the module weight? 11g.
  • What distance should be maintained from the receiver? At least 5cm, as recommended by the manual.
  • Is the maximum current 5A? The supplied manual confirms 3A output but does not specify a 5A peak rating.

Safety Precautions

  • Use batteries within the specified 5.5V–26V input range.
  • Verify the selected 5V or 6V output before connection.
  • Do not exceed the 3A rated output current.
  • Ensure correct input and output polarity.
  • Never connect two BEC positive outputs together without a suitable isolation arrangement.
  • Install the UBEC at least 5cm away from the receiver.
  • Prevent short circuits and exposed wire contact.
  • Keep the module away from water and excessive heat.
  • Disconnect the battery before modifying electrical connections.
  • Ensure the module has adequate ventilation during operation.

Package Includes

  • 1 × 5V/6V 3A Fully Shielded Switch-Mode UBEC Power Supply Module